Jump to content
  • GUESTS

    If You  want access  to member only forums on FM, You will need to Sign-in or  Sign-Up now .

    This box will disappear once you are signed in as a member.

  • 0

Tachometer Problem..


Rost

Question

I glanced down at my tach tonight while cruising along. It was right at 5000 and all of a sudden it just dropped down to nothing. Like I turned the switch off. Any idea why this would happen?....Marine man..are you out there??

Link to comment
Share on other sites

Recommended Posts

  • 0

The one time I had that problem it was the sending unit in the motor that went bad.

Link to comment
Share on other sites

  • 0

I had the same thing happen to me. Not sure what part went bad but it also stopped charging my starting battery

Link to comment
Share on other sites

  • 0

I had the same problem. The tach would go all over the place and my battery wouldn't charge. I think they replaced a part called the Stator (sp).

Link to comment
Share on other sites

  • 0

I've had the same experience on a johnson outboard, after testing the tach against a shop tach we found the problem with the outboards rectifer and strator (part of the voltage regualator and charging system). It is usually caused by an intermittent connection on your cranking battery from the motor. It's always a good idea to replace the wingnuts on your cranking battery with stainless lock nuts or use a needle-nose plier to crank them super tight.

Link to comment
Share on other sites

  • 0

Any idea how much a stator was to replace? Just like Dusty's, my tach was all over the place before going dead as well.

Thanks!

Link to comment
Share on other sites

  • 0

I had the same trouble 2 years ago on my 70hp Jonny. Replaced the stator, problem solved. If I recall correctly, the fix cost me around $300 +/-. I'd suggest if you have an Jonny or Evinrude, you sit down when they quote you. OMC parts prices have skyrocketed in the last few years. When the present parts supply is gone, it's gone. Good luck, Phred52

Link to comment
Share on other sites

  • 0

Thanks Pierbridge, should it happen again, I'll try to remember that. I was only quoting what the local OMC(now Yamaha) mechanic told me <2 weeks ago. And while the aftermarket electronics may be better, I was only trying to say, some parts ARE OEM only. Phred52

Link to comment
Share on other sites

  • 0

What everyone has said so far is correct... or very likely correct.. what do you have for a motor? Unfortunately just about everyone is correct on the price as well...

Have you checked to see if the motor is still charging the starting battery?

marine_man

Link to comment
Share on other sites

  • 0

I just dropped off at the dealership. He was thinking it's the voltage regulator. He said that if it was the stator, the motor would not run at all. Right now it runs perfect. It is a 1997 75 hp Mariner.

Any other ideas?

Link to comment
Share on other sites

  • 0

Rost-

I was out this last weekend and noticed the same thing. I have a '98 Mercury 75. Everything seemed to be running fine, then the tach, fuel gauge and volt meter went hay wire. I'll check it tonight to see if it's still charging the battery. Sure don't want to spend $300 for a new switch box. Let me know what you fine out from the dealer. Thanks!

ERW

Link to comment
Share on other sites

  • 0

No problem. I will let you know. All of your gauges went bad huh? Only my tach went dead. The rest of the gauges work just fine....

Link to comment
Share on other sites

  • 0

It'll be the voltage regulator.... that's a somewhat common occurence on the 75 Merc & Mariner's...

The bad news... I'm guessing you're still looking at $200 to $300 to replace it... it's a snap to replace, but it's one of the electronic boxes / circuit boards on the motors.. that always spells more money...

marine_man

Link to comment
Share on other sites

  • 0

Thanks MM,

Are you a marine mechanic yourself? I am always so impressed with your knowledge of boats and motors. Thank you for always taking the time to help us figure some of this stuff out!

However, you could work on giving us good news rather than the $300 bill news. smirk.gif

Anything else I should watch out for with my 75? Coils? Stator? power pack? Powerhead? Yikes, gives me the shakes just thinking about this stuff!

Link to comment
Share on other sites

  • 0

No problem Rost... no, not a mechanic, but a mechanical engineer who rigged boats and did a little mechanic work on the side while in college and high school... plus I still try and learn as much as possible on marine stuff from all sorts of sources...

I wouldn't anticipate any more problems with your motor... I wouldn't say the voltage regulator is a real common problem... but it is something that happens every now and then.. it certainly isn't on the same scale as a VRO pump on a older Johnson for example.. just something that happens. You've got a good motor... the 75's are pretty much bulletproof... you should be in good shape.

marine_man

Link to comment
Share on other sites

  • 0

Ya, thank you both. I took the boat out tonight. Same problem with the tach. The other gauges are acting goofy too. Based on the volt meter on my depth finder, the battery is still charging when the engine is running. I'm somewhat handy with tools, is a voltage regulator fairly simple to replace? Would like to save a few $$ by doing it myself if the part is going to be spendy.

Thanks again!

ERW

Link to comment
Share on other sites

  • 0

Quote:

.. it certainly isn't on the same scale as a VRO pump on a older Johnson for example..

marine_man


Yikes! Now I'm parnoid. What is a VRO pump? Something tells me it is expensive.

(I don't want to hi-jack this thread, but just curious).

Link to comment
Share on other sites

  • 0

ewirz,

I wouldn't jump to conclusions just yet that it's your voltage regulator as well... it's a pretty expensive part to try replacing if it isn't the problem, because you won't be able to take it back...

Can you describe how your gauges are acting goofy? Erratic movements, not working, what?

In regard to the VRO pump... I believe it stands for variable rate oil injection... and were notrious for problems (ie - not enough oil mixed with gas) in the 80's and 90's on Johnson and Evinrude motors...

marine_man

Link to comment
Share on other sites

  • 0

Here's what I've noticed:

Engine starts, idles, and runs great. Before the tach started acting funny, rpms maxed around 51-5200. Last night when I ran the boat, fuel gauge seemed to be working fine. Tach would go to max (6K) and past. Sometimes would then make a complete revolution back to zero. No reading from dash volt meter. When idling or at low rpm, tach and volt meter would jump around, seemed to affect fuel gauge as well-it would jump slightly too. While doing this, every now and again, the tach and volt would go to a correct reading for the rpm the motor was running at, then start jumping around again. I checked the wiring both at the gauges and at the motor, nothing loose or missing.

Any thoughts? Like you said, I don't want to replace an expensive part just to find out it's not the problem.

Thanks again for the help.

ERW

Link to comment
Share on other sites

  • 0

ERW-

That is exactly what was happening to my tach before it completely went dead. However, I did not notice the volt meter or the fuel gauge jumping around.

Link to comment
Share on other sites

  • 0

It sounds to me like the voltage regulator... but it's hard to be 100% certain without doing some basic testing, for which I don't have the information. If it were just the tachometer I'd say that's got to be it.. but since it's affecting the other gauges it's tough to say for sure... maybe the reason the other gauges are haywire is because of fluctuating voltage?

marine_man

Link to comment
Share on other sites

  • 0

I went back into my records and found that the dealer first replaced the rectofier and the regulator. I got the rig back and it still wasn't charging or at least according to my voltage meter on the boat and my tach was jumping all over the place. They then replaced the stator. The motor was under warranty so I don't know the cost to replace the parts. My motor is an 2002 115 hp Yamaha on a Crestliner

Link to comment
Share on other sites

  • 0

Rost, you said boat is at the dealer, correct ?

I would guess rectifier (regulator) too, but could be wrong.

If you need another tachometer to test yours, I can send you one.

Another issue it could be it the adjustment on back of gauge. There is a small screw you have to turn to the settings your motor has, it might got a little corroded and give false reading, try to turn it both ways then reposition it, you can do it while motor is running.

Faria5set3.jpg

Link to comment
Share on other sites

  • 0

Correct me if I'm wrong Valv... but wouldn't a incorrect pole setting on the tach result in false (too high, too low) RPM readings, and not erratic, or no readings at all?

marine_man

Link to comment
Share on other sites

  • 0

Well guys, the drama is over. The dealer called and informed me that it was simply a bad tach!!!!! Wow, what a relief! I do appreciate all of the help everyone has offered! Thanks again..

Link to comment
Share on other sites

  • 0

You are correct Marine_man but since it was an erratic function I thought maybe it was making bad contact.

Link to comment
Share on other sites

  • 0

I'm glad it was just a tach... in my opinion that really underscores the whole reason for conducting the proper tests, etc on a motor before just replacing parts... in this case you probably saved yourself about $300 by not just replacing parts and actually finding the root cause before replacing parts. We can all make educated guesses as to what the problem might be, but until one really gets into it they're all just suggestions of what to look for...

marine_man

Link to comment
Share on other sites

  • 0

Ehm...if you start with tachometer and you buy it from KV Enterprises (me) it's only $ 12.50..... grin.gif

That's a cheap way to troubleshoot.....right Rost ????

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • mulefarm
      With the early ice out, how is the curlyleaf pondweed doing?
    • LakeofthewoodsMN
      On the south end...   The big basin, otherwise known as Big Traverse Bay, is ice free.  Zippel Bay and Four Mile Bay are ice free as well.  Everything is shaping up nicely for the MN Fishing Opener on May 11th. With the walleye / sauger season currently closed, most anglers are targeting sturgeon and pike.  Some sturgeon anglers are fishing at the mouth of the Rainy River, but most sturgeon are targeted in Four Mile Bay or the Rainy River.  Hence, pike are the targeted species on the south shore and various bays currently.   Pike fishing this time of year is a unique opportunity, as LOW is border water with Canada, the pike season is open year round. The limit is 3 pike per day with one being able to be more than 40 inches. All fish 30 - 40 inches must be released. Back bays hold pike as they go through the various stages of the spawn.  Deadbait under a bobber, spinners, spoons and shallow diving crankbaits are all viable options.   Four Mile Bay, Bostic Bay and Zippel Bay are all small water and boats of various sizes work well. On the Rainy River...  Great news this week as we learned sturgeon will not be placed on the endangered species list by the U.S. Fish and Wildlife Service.     The organization had to make a decision by June 30 and listing sturgeon could have ended sturgeon fishing.  Thankfully, after looking at the many success stories across the nation, including LOW and the Rainy River, sturgeon fishing and successful sturgeon management continues.   A good week sturgeon fishing on the Rainy River.  Speaking to some sturgeon aficionados, fishing will actually get even better as water temps rise.     Four Mile Bay at the mouth of the Rainy River near the Wheeler's Point Boat Ramp is still producing good numbers of fish, as are various holes along the 42 miles of navigable Rainy River from the mouth to Birchdale.   The sturgeon season continues through May 15th and resumes again July 1st.   Oct 1 - April 23, Catch and Release April 24 - May 7, Harvest Season May 8 - May 15, Catch and Release May 16 - June 30, Sturgeon Fishing Closed July 1 - Sep 30, Harvest Season If you fish during the sturgeon harvest season and you want to keep a sturgeon, you must purchase a sturgeon tag for $5 prior to fishing.    One sturgeon per calendar year (45 - 50" inclusive, or over 75"). Most sturgeon anglers are either a glob of crawlers or a combo of crawlers and frozen emerald shiners on a sturgeon rig, which is an 18" leader with a 4/0 circle hook combined with a no roll sinker.  Local bait shops have all of the gear and bait. Up at the NW Angle...  A few spots with rotten ice, but as a rule, most of the Angle is showing off open water.  In these parts, most are looking ahead to the MN Fishing Opener.  Based on late ice fishing success, it should be a good one.  
    • leech~~
      Nice fish. I moved to the Sartell area last summer and just thought it was windy like this everyday up here? 🤭
    • Rick G
      Crazy windy again today.... This is has been the norm this spring. Between the wind and the cold fronts, fishing has been more challenging for me than most years.  Panfish have been moving in and out of the shallows quite a bit. One day they are up in the slop, the next they are out relating to cabbage or the newly sprouting lilly pads.  Today eye guy and I found them in 4-5 ft of water, hanging close to any tree branches that happened to be laying in the water.  Bigger fish were liking a 1/32 head and a Bobby Garland baby shad.   Highlight of the day way this healthy 15incher
    • monstermoose78
    • monstermoose78
      As I typed that here came a hen.  IMG_7032.mov   IMG_7032.mov
    • monstermoose78
      So far this morning nothing but non turkeys. 
    • monstermoose78
      Well yesterday I got a little excited and let a turkey get to close and I hit the blind!!
    • smurfy
      good......you?? living the dream..in my basement playing internet thug right now!!!!!! 🤣 working on getting the boat ready.......bought a new cheatmaster locator for the boat so working on that.   waiting for warmer weather to start my garden!!!
    • monstermoose78
      How is everyone doing? Holy moly it’s chilly this morning I stayed in bed and will hunt later today when it warms up.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.