Jump to content
  • GUESTS

    If You  want access  to member only forums on FM, You will need to Sign-in or  Sign-Up now .

    This box will disappear once you are signed in as a member.

OutdoorMN News - Small fire burning in Itasca State Park (published October 6, 2021)


Recommended Posts

  • 'we have more fun' FishingMN Creators
At approximately 3:30 p.m., Tuesday, Oct. 5, Clearwater County Sheriff’s Department received a report of a fire burning in timber, lowland grasses and brush in a remote location in Itasca State Park, at the end of Bohall Trail and on the north side of Bohall Lake.

Discuss below - to view set the hook here.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Your Responses - Share & Have Fun :)

    • leech~~
      My wife is from Brainerd and has a lot of relatives up there. More then likely it would be Baxter or above Brainerd. 
    • Wanderer
      Heat can cause some issues.  Like an old PTO on a lawn tractor that won’t engage after it’s been running, then shut off, then turned on again.  Having to wait 2-3 hours to get it to engage again tells you it’s time at least adjust it but plan on a replacement soon.
    • Tom7227
      I can't figure  out how enough heat would form to cause a problem. What part could be getting hot?  That sort of makes sense but then it will start and quit again quite quickly.  I don't  know what engine it has and that's a problem with it.  Finding the parts is troublesome even with Jack's Small Engine.
    • smurfy
      thats the engine on the one i have.
    • delcecchi
      The not restarting for hours....   Could it possibly be an ignition thing where as it gets hot it stops providing spark and has to cool all the way down to start again?     That's the only thing besides flooding I can think of.   Typically, isn't the spark on small engines produced by magnets on the flywheel going by a coil?    So when it quits and won't restart, is it getting spark?      And is the plug wet when it quits?        Has it got the Honda motor or something else?   
    • smurfy
      That's odd Tom, I have a power washer from northern tool also. Not sure which one but only issues I've had with mine is I had to replace both tires???🙄🙄
    • Tom7227
      Full throttle before I even start to spray.  When trying to restart it pulls easy and I keep the wand open to assure it doesn't get backed up.  I agree it has to be a fuel issue.  But the tank to engine line is a straight shot except for the fuel shut off valve.  When I was replacing the carb the fuel would run out of the fuel line quite a bit until I remembered to shut off the fuel line.   The gas has been brand new non-oxy every time I have tried it.  
    • Wanderer
      When you try to restart it does it pull easy or hard?   When mine has water pressure built up, it pulls hard to start.  I trigger the wand to release the pressure so it starts easier.   Maybe the hours for yours is due to pressure that needs to bleed off?  Hard to tell not being there.     I can kill mine at low throttle just by spraying.  Are you running yours at a high throttle position?  Again, hard to tell without hearing the RPMs of the engine.   Otherwise for fuel, it could be a blockage or venting issue anywhere in the system. If there wasn’t a change in performance with the change of carburetor, the carburetor is probably not the issue.  If it sat with old gas for a while something could be varnished up and the engine starves for gas until it quits.  Taking hours to get enough fuel flowing again to run seems odd if you actually get to run it hard enough to spray for even a few minutes.   Hearing the way it behaves would help a lot for me.   I’ve had pressure washers that you’re not supposed to let idle for extended time without spraying and others like my current one that bypass just fine while it’s running.  I’m just wondering if your killing it on high pressure AND low idle.  Mine will die every time that way.
    • Tom7227
      It is a Powerhorse, the northern tool house brand.  It dies while I am spraying.  If I replaced the carb what more fuel issues could there be?  The carb replacement took about 5 minutes and was extremely simple.
    • JerkinLips
      I retired 2½ years ago.  My wife finally agreed to move up north after she retires the end of 2021.  When she retires there is nothing that would keep us in the cities.  Blaine has been very peaceful over these turbulent times, but I have a lot of buckshot for my three 12ga shotguns just to be safe.  Anywhere from Barnum to Soudan would be fine for us (easy day trip to Vermilion).  Would go as far west as Grand Rapids.  Would love to live on Vermilion but the prices are just too high now.  Best of luck to you.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.