Jump to content
  • GUESTS

    If You  want access  to member only forums on FM, You will need to Sign-in or  Sign-Up now .

    This box will disappear once you are signed in as a member.

  • 0

Pro-V Tiller Question


CabinBoy

Question

I've got a '03 1800 Pro-V tiller and am getting ready to install the electronics. What is the best way to run the cable from the transducer to the electronics center? Also, are there just one set of wires coming from the fuse panel to connect all elctronics too? Thanks for the help.

Link to comment
Share on other sites

3 answers to this question

Recommended Posts

  • 0

cabinboy I have a 96 pro v and I ran the xducer cable through the backsplash drain than I cut the lower back corner of the command center at a 45 degree angle in the lower back corner and bushed it with a split chunk of tubing just to protect the wire from abrasion. Get some small cable straps in assorted sizes to keep the cable's in place. On the rear of the transom I have a plastic mounting board that holds my xducer and speed wheel. Where there was a location in which I didn't want to put a screw I used adhesive backed cable tie anchors and a plastic cable tie. as to the question of where to power the electronics up my fuse block has 2 fused accessories points to lay the wires down on

[This message has been edited by waterwolff (edited 02-15-2004).]

Link to comment
Share on other sites

  • 0

waterwolff-
Is your fuse panel on the same side as your elec. command center? On mine they are on opposite sides of the boat and I can only find one pos./neg. set of wires coming to the command center.

Link to comment
Share on other sites

  • 0

Yes it is on the same side. Mine is located on the lower left corner of the command center. When you remove your panel cover how many acc. spots are labeled it may just be a simple job of pulling another circuit over to your command center. You no doubt will have flex tube coming from your fused terminal block into accessible areas of your boat to get back and forth if not directly to the command center from the fuse block. If you want you can call me at 651-755-0646

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • FrankOcean
      If your company is very large and has many employees, you will have to hire a professional company that is specifically dedicated to that, since a single professional will not be able to do everything, in the google search bar you can find many, but if someone here can recommend you one that has used it as much as possible is much better, good luck to your company and to you!
    • PSU
      61 this afternoon in Frazer/Smarts. I'll comment later as I haven't been out yet 
    • leech~~
      BW is not a designated Trout lake. The limit is the same as state which I think is 5 bows. Don't think there is a size limit either since they don't breed. 
    • King of walleyes
      What is the slot on trout in big waltab lake mn  jw size and how many can u keep
    • Sawbuck
      Rotes, Hi, I just joined this forum and these corner caps are just what I have been looking for. Is it possible at this late date to get a set of these made for my Lund? The only difference I can see is the color of the material. Would you be willing to make a set for me? Thanks, [email protected]
    • Colin45
      Any move requires time and effort, but if you turn to a moving company for help, then some of the problems will disappear immediately. Firstly, the guys from the moving services always take care of the client's property, pack and carefully transfer your things to the car. Secondly, when moving with movers, you do not have to worry about the road, they choose the fastest and safest way, as they have extensive experience in transportation.
    • SkunkedAgain
      Anybody know how much the lake temps have dropped?   Are people have the most success with minnows vs crawlers when fishing with live bait lately, or are crawlers still working?
    • Kettle
      Snuck out last night, water Temps down to 54-56, last Thurs mid 60s. Fish were finicky. Leaves are changing quickly here, lots falling. Two weeks should be a lot better in the woods
    • valtt79
      I agree with the previous comment, you could save a lot of money by making your website first .. its design .. and then if you want to move .. but if you want, you can immediately ..-) look here: https://digitalsuits.co/hire-developers/hire-shopify-developers/
    • valtt79
      I think that even at the initial stage, you need to consult with specialists who have been working in this field for a long time .. and then you will really get the result .. otherwise you can spend a lot of time and in the end you will have to redo everything .. for example, look here: https://www.softformance.com/services/software-consulting-company/
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.