Jump to content
  • GUESTS

    If You  want access  to member only forums on FM, You will need to Sign-in or  Sign-Up now .

    This box will disappear once you are signed in as a member.

  • 0

Used motor been sitting for 3 years! What should I do first?


Finlander

Question

The gas tank is almost full and what should I do with gas thats been sitting for that long?
Any suggestion as to what to do to get this motor ready for the duck season.
It's a 1980 15hp Johnson only used during the duck seasons.

Link to comment
Share on other sites

4 answers to this question

Recommended Posts

  • 0

I'm certainly no mechanic, but I'd start by draining the gas. You'll have to bring that in as hazardous waste someplace that will accept it most likely - an auto parts store might take it, I know some take used oil..

I'd spray up the carburetor with some type of carb. cleaner and replace the spark plug. Fresh gas and a new spark plug may be all you need to do depending on the condition of the motor. Good luck!

Link to comment
Share on other sites

  • 0

Got any wood? You could probably do a lot of varnishing...

sorry... couldn't resist... tongue.gif

Link to comment
Share on other sites

  • 0

Fishinaddict is correct.
Here's what I usually do:
Empty tank and dispose of gas properly (I use it in my old Allis tractor).
Remove carburator and clean it up very well with spray carb cleaner.
Pull the plugs and spray some WD40 or oil into cylinders, then turn flywheel few times to help lubricate cylinder walls.
Replace plugs and re install them.
It will be better to pull lower unit and replace water pump impeller, but on Evinrude you will have to disconnect shift rod right below carb (while it's off) or somewhere on the center section of motor (this will be a little tought to do, depending on your mechanical skills).
After this motor should be ready to go, check all hoses and wires for cracks or bruises and recplace if needed.
Start motor in a tank or with muffs, if it runs by itself with no problem, you are set, if it dies and you have to pump gas with primer, you will have to replace fuel pump also, but don't buy a kit, they are a pain to reassemble, buy the whole unit, it's slightly more expensive.
If you have a manual, it will help a lot.
Good luck.

Link to comment
Share on other sites

  • 0

I'd spray fogging oil into the cylinders while gently turning over the motor. WD40 is a not a lubricant contrary to popular belief.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.


  • Your Responses - Share & Have Fun :)

    • Conan Bail
      Yes, you can make good money at the casino, but I think that this is unstable earnings, and situational, if you play every day, you can get into very large debts. I was advised this casino - https://onlinecasinospill.no/ , I tried and made no mistake in choosing, there is a huge bonus system, constant promotions for any holidays and a bunch of different slots that only improve the game, also the probability of winning is quite high, I was able to earn a small amount of money, I advise you to try
    • Conan Bail
      Филипп 9:29 In order to avoid unplanned expenses, you need to immediately discuss all the nuances with the contractor. In fact, there are many options. But it still seems to me that it can be done independently, even bulky things with several people can be loaded and moved on by themselves
    • Andre.y
      I agree with you, but not completely, because you can win once and bet a little more, that is, set aside 80% of the total amount, and then play for the remaining 20%, I think this is a good option, and in any case, a person will win
    • Andre.y
      As far as I know, there are several companies in Boston that are engaged in full professional relocation, it takes a little time, but they take enough money, I saw a couple of ads on the Internet about such work, you can also find performers of this order there
    • Giles
      For a long time I wanted to turn to a good programmer so that he would collect applications for mining for me, but I could not find it and abandoned this business, now this thought is returning. I came up with such an application that no one has, but no one can assemble it, everyone refuses. I looked at the site that you advise, quickly read it, this company made a good impression on me, I will carefully read it in the evening, then I will contact them and if they agree with my idea, I will order.
    • Rick G
      @leech. Translation please???😂🤷. Might be a hot fishin'report and I can't read it😂
    • Rick G
    • JBMasterAngler
      Slow weekend. Soaked crawlers at various spots above and below the dam. Only a couple mooneye and little redhorse to show for it.
    • Rick G
      Now you know darn well your not in Boston....unless there's a Boston in russia?😂😂😂 How's life over there?💩.  
    • Rick G
      The creek  bite has been nothing short of awesome as we come to the end of Sep.... Some days are definitely better than others, but even the slow days plenty of fish can be caught if you put in a little time and effort.   3 and 4 inch z-man plastics as well as grub style plastics have been getting the job done for me again this week.  Also been using some number 5 shad raps just to change things up a bit... 😁
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.